ifconfig命令详解

2023年10月8日 402次阅读 来源: SophieSg

参数

-a 显示全部接口信息

[root@controller hello]# ifconfig -a
enp0s3: flags=4419<UP,BROADCAST,RUNNING,PROMISC,MULTICAST>  mtu 1500
        inet 192.168.10.202  netmask 255.255.255.0  broadcast 192.168.10.255
        inet6 fe80::a00:27ff:febc:4068  prefixlen 64  scopeid 0x20<link>
        ether 08:00:27:bc:40:68  txqueuelen 1000  (Ethernet)
        RX packets 132991  bytes 86829278 (82.8 MiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 73175  bytes 13137262 (12.5 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

enp0s8: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.56.102  netmask 255.255.255.0  broadcast 192.168.56.255
        inet6 fe80::a00:27ff:fe78:76c3  prefixlen 64  scopeid 0x20<link>
        ether 08:00:27:78:76:c3  txqueuelen 1000  (Ethernet)
        RX packets 15992  bytes 1550956 (1.4 MiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 6044  bytes 1022821 (998.8 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1  (Local Loopback)
        RX packets 15273888  bytes 1929203265 (1.7 GiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 15273888  bytes 1929203265 (1.7 GiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

-s 显示摘要信息

[root@controller hello]# ifconfig -s
Iface      MTU    RX-OK RX-ERR RX-DRP RX-OVR    TX-OK TX-ERR TX-DRP TX-OVR Flg
enp0s3    1500   133056      0      0 0         73204      0      0      0 BMPRU
enp0s8    1500    15995      0      0 0          6048      0      0      0 BMRU
lo       65536 15278612      0      0 0      15278612      0      0      0 LRU

启动或关闭指定网卡

ifconfig eth0 up
ifconfig eth0 down
ifup eth0
ifdown eth0

-promisc 设置是否支持网卡的promiscuous模式

如果选择此参数，网卡将接收网络中发给它所有的数据包

ifconfig eth0 promisc  ／／设置
ifconfig eth0 -promisc ／／取消

-allmulti 设置是否支持多播模式

ifconfig eth0 allmulti  ／／设置
ifconfig eth0 -allmulti ／／取消

如果选择此参数，网卡将接收网络中所有的多播数据包

配置IP地址

ifconfig eth0 192.168.120.56 
ifconfig eth0 192.168.120.56 netmask 255.255.255.0 
ifconfig eth0 192.168.120.56 netmask 255.255.255.0 broadcast 192.168.120.255

单网卡添加多个IP地址

ifconfig eth0:0 192.168.0.1 netmask 255.255.255.0 up
ifconfig eth0:1 192.168.0.2 netmask 255.255.255.0 up

删除IP地址

ifconfig eth0 del 192.168.227.188

启用或关闭arp协议

ifconfig eth0 arp
ifconfig eth0 -arp

设置最大传输单元

设置能通过的最大数据包大小为 1500 bytes

ifconfig eth0 mtu 1500

用ifconfig修改MAC地址

ifconfig eth0 hw ether 00:AA:BB:CC:DD:EE

注意：使用ifconfig配置的网络信息，在网卡重启或者机器重启之后就失效了。如需永久保留，请在配置文件中持久化保存。

    原文作者：SophieSg
    原文地址: https://www.jianshu.com/p/92c65533d72a
    本文转自网络文章，转载此文章仅为分享知识，如有侵权，请联系博主进行删除。
点赞