解压文件
dfzxk@satan-master:~$ cd /home/dfzxk/下载/
dfzxk@satan-master:~/下载$ ls -a
. homework MacBuntu-Wallpapers package.crx
.. john-1.8.0.tar.gz netease-cloud-music_1.1.0_amd64_ubuntu.deb
dfzxk@satan-master:~/下载$ tar -zxvf john-1.8.0.tar.gz
john-1.8.0/README
john-1.8.0/doc/CHANGES
......
dfzxk@satan-master:~/下载$ ls -a
. homework john-1.8.0.tar.gz netease-cloud-music_1.1.0_amd64_ubuntu.deb
.. john-1.8.0 MacBuntu-Wallpapers package.crx
进入目录，看相关信息
dfzxk@satan-master:~/下载$ cd john-1.8.0/
dfzxk@satan-master:~/下载/john-1.8.0$ ls -a
. .. doc README run src
dfzxk@satan-master:~/下载/john-1.8.0$ cat README
John the Ripper password cracker.
John the Ripper is a fast password cracker, currently available for
many flavors of Unix (11 are officially supported, not counting
different architectures), Windows, DOS, BeOS, and OpenVMS (the latter
requires a contributed patch). Its primary purpose is to detect weak
Unix passwords. Besides several crypt(3) password hash types most
commonly found on various Unix flavors, supported out of the box are
Kerberos/AFS and Windows LM hashes, as well as DES-based tripcodes, plus
many more hashes and ciphers in "community enhanced" -jumbo versions
and/or with other contributed patches.
How to install.
See INSTALL for information on installing
John on your system.
查看安装信息
dfzxk@satan-master:~/下载/john-1.8.0$ cd doc/
dfzxk@satan-master:~/下载/john-1.8.0/doc$ ls -a
. CHANGES CONTACT CREDITS EXTERNAL INSTALL MODES README
.. CONFIG COPYING EXAMPLES FAQ LICENSE OPTIONS RULES
dfzxk@satan-master:~/下载/john-1.8.0/doc$ more INSTALL
Installing John the Ripper.
First of all, most likely you do not need to install John the Ripper
system-wide. Instead, after you extract the distribution archive and
possibly compile the source code (see below), you may simply enter the
"run" directory and invoke John from there.
System-wide installation is also supported, but it is intended for use
by packagers of John for *BSD "ports", Linux distributions, etc., rather
than by end-users. (If you're in fact preparing a package of John,
please refer to the JOHN_SYSTEMWIDE setting in src/params.h.)
You may have obtained the source code or a "binary" (pre-compiled)
distribution of John the Ripper. On Unix-like systems, it is typical
to get the source code and compile it into "binary" executables right
on the system you intend to run John on. On DOS and Windows, however,
it is typical to get a binary distribution which is ready for use.
The following instructions apply to the source code distribution of
John only. If you have a binary distribution, then there's nothing
for you to compile and you can start using John right away.
Compiling the sources on a Unix-like system.
Enter the directory into which you extracted the source code
distribution of John. Enter the "src" subdirectory and invoke "make"
to obtain a list of operating systems for which specific support
exists:
cd src
make
Note the make target for your system and type:
make clean SYSTEM
where SYSTEM is the appropriate make target. Alternatively, if your
system is not listed, use:
make clean generic
If everything goes well, this will create the executables for John and
its related utilities under "../run/". You can change directory to
there and start John, like this:
cd ../run
./john --test
Alternatively, you may copy the entire "run" directory to anywhere you
like and use John from there.
安装软件
dfzxk@satan-master:~/下载/john-1.8.0/src$ make | more
To build John the Ripper, type:
make clean SYSTEM
where SYSTEM can be one of the following:
linux-x86-64-avx Linux, x86-64 with AVX (2011+ Intel CPUs)
linux-x86-64-xop Linux, x86-64 with AVX and XOP (2011+ AMD CPUs)
linux-x86-64 Linux, x86-64 with SSE2 (most common)
........
dfzxk@satan-master:~/下载/john-1.8.0/src$ make linux-x86-64-avx
ln -sf x86-64.h arch.h
make ../run/john ../run/unshadow ../run/unafs ../run/unique \
JOHN_OBJS="DES_fmt.o DES_std.o DES_bs.o DES_bs_b.o BSDI_fmt.o M
这个安全试验，已经放弃了，没有精力和时间去做了。
以后可能会补起来。
